SEESII Tinysa Spectrum Analyzer 2.8" Screen Handheld Frequency Analyzer Signal Generator 100kHz to 960MHz MF/HF/VHF UHF Input

2.8INCH OPTION: Upgraded Hand held tiny Spectrum analyzer TinySA 2.8" display 100kHz to 960MHz with ESD proteced Version V0.3.1_E Specification

User interface:

* Display resolution 320*240 pixels * Screen diagonal 2.8" * 16 bits per RGB pixels * Resistive touch control * Jog switch control * USB serial port control * Optional TTL USART port (SW not yet implemented) on the internal PCB * Linear power supply to avoid switching noise. *Add port ESD protection to upgrade version(V0.3.1_E)

The input/output specification of the tinySA is split over the 4 modes

Low input mode spec:

* Input frequency range from 100kHz to 350MHz * Input impedance 50 ohm when input attenuation set to 10dB or more. * Selectable manual and automatic input attenuation between 0dB and 31dB in 1 dB steps * Absolute maximum input level without attenuation of +10dBm * Absolute maximum input power with 30dB attenuation of +20dBm for short period * Input Intercept Point of third order modulation products (IIP3) with 0dB attenuation of +15dBm * 1dB compression point at +2dBm with 0dB attenuation * Power detector resolution of 0.5dB and linearity versus frequency of +/-1dB * Absolute power level accuracy after power level calibration of +/- 1dB * Lowest discernible signal using a resolution bandwidth of 30kHz of -102dBm * Frequency accuracy equal to the selected resolution bandwidth * Phase noise of -90dB/Hz at 100kHz offset and -115dB/Hz at 1MHz offset * Spur free dynamic range when using a 30kHz resolution bandwidth of 70dB * Manually selectable resolution filters of 3, 10, 30, 100, 300, 600kHz. Automatic selection of one of the 57 resolution filters. * On screen resolution of 145 or 290 measurement points. * Scanning speed of over 1000 points/second using largest resolution filters. * Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth * Spur suppression option for assessing if certain signals are internally generated or actually present in the input signal

High input mode spec:

* Input frequency range from 240MHz to 960MHz * As there is no input bandfilter strong signals outside the 240MHz to 960MHz range can cause distortion of the in band signals * Absolute maximum input level without attenuation of +10dBm * Input Intercept Point of third order modulation products (IIP3) of -5dBm * 1dB compression point at -6dBm with 0dB attenuation * Power detector resolution of 0.5dB and linearity versus frequency of +/-1dB * Absolute power level accuracy after power level calibration of +/- 1dB * Lowest discernible signal using a resolution bandwidth of 30kHz of -115dBm * Frequency accuracy equal to the selected resolution bandwidth * Spur free dynamic range when using a 30kHz resolution bandwidth of 50dB * Selectable (automatic and manual) resolution filters of 3, 10, 30, 100, 300 and 600kHz * Optional 25dB to 40dB frequency dependent input attenuator. The power level error with this attenuator activated increases to +/- 15dB * On screen resolution of 145 or 290 measurement points. * Scanning speed of over 1000 points/second using largest resolution filters. * Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth

Low output mode spec:

* Sinus output with harmonics below -40dB of fundamental * Output frequency range from 100kHz to 350MHz * Output level selectable in 1dB steps between -76dBm and -6dBm * Optional AM, narrow FM and wide FM modulation or slow sweep over selectable frequency span

High output mode spec:

* Square wave output * Output frequency range from 240MHz to 960MHz * Output level selectable in variable increments between -38dBm and +13dBm * Optional narrow FM and wide FM modulation or slow sweep over selectable frequency span

Reference generator spec:

* Optional square wave output with fundamental at -25dBm connected to high input/output * Frequency can be set to 1MHz, 2MHz, 4MHz, 10MHz, 15MHz or 30MHz.

Battery spec:

* Charging time max 1 hour on 500mA minimum USB port or USB charger * Operation on fully charged battery for at least 2 hours

Package inclued: TinySA 2.8" Spectrum analyzer *1 20cm sma-sma rg174 rf cabe *2 USB Type-C Data Cable *1 Hand rope *1 SMA female to female connector  *1 SMA telescopic antenna *1

4.0INCH ZS406OPTION SeeSii TinySA Ultra+ ZS406 Spectrum Analyzer, 4.0 Inch 100kHz to 5.4GHz Handheld Tiny Frequency Analyzer with 32Gb Card, 2-in-1 Signal Generator MF/HF/VHF UHF Input,V0.4.6.1, Upgraded

Upgraded ZS406 TinySA Ultra+:This New Version V0.4.6.1 Spectrum Analyzer is developed by Hugen, with 4.0 inch 480 x 320 large touchscreen display, 100kHz to 5.4GHz widely measure range, with the new ESD protection function, the product has a higher anti-static level and a longer service life, and built-in 32Gb micro SD card, can directly record data to the card ,which is convenient for your data sharing and storage

Widely Frequency Range: Compared to the tinysa (100kHz to 960MHz), the upgraded tinysa ULTRA+ has 100kHz to 5.4GHz ultra-wide measuring frequency range, spectrum analyzer for 0.1-800MHz, with Ultra mode up to 0.1MHz-6GHz.Switchable resolution band pass filters for both ranges between 200Hz to 850kHz. Color display showing 450 scan points covering up to the full low or high frequency range. Faster and more accurate measurement performance, you can easily cope with measurement testes in various fields

2 in 1 Multifunctional Frequency Analyzer & Signal Generator:When not used as Spectrum Analyzer it can be used as Signal Generator,with sine wave output between 0.1-800MHz or square wave or dual tone output up to 4.4GHz.Built-in calibration signal generator that is used for automatic self test and low input calibration

PC Control: Connected to a PC via USB it becomes a PC controlled Spectrum Analyzer or Signal Generator.Tinysa-APP transfers data directly to the computer.The USB interface implements CDC protocol and there is a large set of commands that can be invoked over the serial interface. These command can be used to perform measurements or update internal settings. The driver for Windows will install automatically after connecting to a Windows PC. The driver for Linux is built into the kernel

Ultra-long Battery Life: The upgraded tinysa analyzer built-in 5000m-ah rechargeable battery,with type-C charging cable and LED charging indicator,it can be fully charged within 3 hours,no need to charge frequently

Excellent Phase Noise Performance: With advanced spectrum analyzer, especially tinysa ultra, outstanding phase noise performance is shown. At 30MHz, phase noise is -108dB/Hz at 100kHz offset and -115dB/Hz at 1MHz offset. DANL is -166dBm/Hz. There's an LNA in the level menu, which offers 20dB extra gain for low - level signals (LNA in tinysa ultra works only below 3.5GHz). The default max frequency is 800MHz. No need to switch frequency ranges, and you can monitor the whole range in one sweep

Package Contents: 1x ZS406 Tinysa ULTRA+ Spectrum Analyzer (built-in 5000mah rechargeable battery), 1x 32GB Micro SD card (plugged in the host) 2x 30cm ALSR100 SMA cables,1 x USB Type-C data cable, 1x SMA-SMA barrel connector,1x TLanyard and touch plectrum; 1x Antenna with SMA connector, 1x stylus touch pen

Battery Included: Yes Origin: Mainland China High-concerned chemical: None Semi-finishedproduct: No DIY Supplies: Electrical